Extron electronic Stereo System DMP 64 User Manual

DMP 64 Setup Guide  
This guide provides basic instructions for an experienced technician to install the DMP 64 ProDSPDigital Matrix Processor.  
Where possible in the following pages, line drawings and photos from an actual installation are used to clarify steps  
discussed in the text. Where appropriate, images have one or more numbers corresponding to a specific step described.  
Chapter number and titles reference the DMP 64 User's Manual found at www.extron.com.  
Step 1 — Disconnect power  
Disconnect power to the DMP 64 and turn off all devices that will be connected to it.  
Step 2 — Mount the DMP 64  
The DMP 64 is housed in a 1/2 rack width, 9.5" deep, 1U high metal enclosure. Select a suitable mounting location,  
then choose an appropriate mounting option. See Chapter 2, "Installation", for additional information.  
Step 3 — Cable the Digital Matrix Processor  
Run all audio, communication and power cables for operation to the rear panel.  
1
3
1
2
RS-232(1)  
2
5
I/O  
MIC/LINE INPUTS  
DMP 64  
O
U
T
Tx Rx  
1
4
2
3
6
LAN  
MIC  
+48V  
POWER  
P
U
T
5
3
4
RS-232(2)  
6
RESET  
4
3
6
1
4
2
5
S
12V  
1.5A MAX  
Tx Rx  
h
d
e f g g  
Step 4 — Connect the Mic/Line inputs  
Attach up to 6 mic or mono line level devices, balanced or unbalanced, to  
the DMP 64 using the wiring diagram to the right.  
Tip  
Tip  
Ring  
Sleeve  
Step 5 — Connect the audio outputs  
Sleeve  
For balanced or unbalanced mono audio output, connect an audio output  
device to each of the four outputs. Use the wiring diagram to the right.  
Unbalanced  
Balanced  
Do not tin the wires!  
Step 6 — Connect the I/O ports  
1
2
3
_
To control or monitor external devices, connect up to 6 digital I/O ports. See  
Chapter 3, "Rear Panel Operation" and Chapter 5, "Digital I/O Ports" for  
additional information.  
Digital I/O Wiring  
Step 7 — Connect a control system  
Extron recommends using the LAN port for configuration and remote  
control of the DMP 64. However there are three options; RS-232,  
USB and LAN. See Chapter 2, "Rear Panel Features and Cabling"  
for additional information.  
RS-232  
Device  
Bidirectional  
RS-232 — Connect the host RS-232 cable to the 3-pin captive screw  
connector on the rear of the switcher.  
Transmit (Tx)  
Receive (Rx)  
Transmit (Tx)  
Receive (Rx)  
Do not tin  
the wires!  
Ground (  
)
Ground (  
)
USB — Connect the host USB port to the front configuration port  
using a USB to mini-USB cable.  
IP Address: 192.168.254.254  
Subnet Mask: 255.255.0.0  
Default Gateway: 0.0.0.0  
DHCP: OFF  
LAN — Using a standard ethernet cable, connect to the network via  
the LAN port ( ). To connect the DMP 64 directly to a computer,  
i
use a crossover ethernet cable. The table at right shows the default  
network settings.  
68-1790-50 Rev. A  
10 09  
 

Eiki Projector AH 45201 User Manual
Electro Voice Stereo Amplifier P 3000 User Manual
Exido Hair Dryer Hairdryer User Manual
Focal Car Speaker 130 CA1 User Manual
Friedrich Universal Remote PDXRC User Manual
Fujitsu Server T5120 User Manual
Fundex Games Games Disc Master User Manual
GE Automobile Accessories WSM2700 80D User Manual
Gianni Industries Switch CP 21 GE User Manual
Gianni Industries Switch TS 980 User Manual